Clay Plastering Strawbales - SECOND COAT

I would like to address issues & tips for the 2nd coat of clay plaster on strawbale walls today. Note, I am assuming you are using clay plaster for all 3 layers of a 3-coat application. For tips on applying the 1st coat of clay plaster, see my previous post "Clay Plastering Strawbales - FIRST COAT". For information on finish plastering, see "Finish Clay Plaster & Wall Preparation".

GOAL for 2nd coat of plaster
The goal for the 2nd coat of plaster is to sculpt the walls into the desired shape.  The first coat created your amazing bond to the strawbales.  And your finish coat will create the texture you desire.  This second coat is where you create the shape you want your walls to have.  Your shaping/sculpting plaster is bonding directly to the first coat of clay plaster you applied, so the bond of that first coat is essential.  Since your first coat usually is lumpy & bumpy, you have excellent surface area to physically key your second coat of plaster to the first coat.

transformation from 1st coat (left) to 2nd coat (right)

In this coat of plaster, I care very much what it looks like...not how it feels, but how the shape looks.  I try to minimize or avoid cracks, I work sculpted areas a lot so they look exactly how I want them to, and I spend as much time as needed to shape the wall into something that is beautiful to me.  Then I'm well-prepared for a nice, even coat of finish plaster, where I can work on texture.

WALL PREPARATION for 2nd coat of plaster
1. Work any loose spots - I go around the dry first coat of plaster and make sure there are no loose spots.  There will usually be a wide, tell-tale crack if you have a loose spot at a strawbale seam, where the first plaster was not worked in well.  I also check corners, around windows, and the tops of walls, to be sure all the walls feel nice and dense and tight.

2. Make test plaster mixes - I make several test plasters and apply them directly onto the first layer of clay plaster.  What I'm experimenting with in my tests are the proportions of ingredients.  Since I use almost exclusively clay soils to make plasters, it means I'm using different clay each time, and each clay has different properties.  So I make test areas at least 24" x 24" in area with varying proportions of clay and sand, and I write my proportions directly into the plaster surface.  When the test areas dry, I look for the one that cracks the least, but that I can press into firmly with my thumb and it is not crumbly or dust, but nice and firm.

3. Wet the walls down - I can't stress this one enough, and as I mentioned in the post on 1st coats of plaster, this is the most common error I see...applying plasters over dry substrates!  I hose down the 1st coat of clay plaster the evening before I plan to plaster, again in the morning, again about 30 minutes before plastering, and then continually as the wall dries out over the course of working.  If the 1st coat of plaster is dry, the clay sucks moisture out of the 2nd coat of plaster, and causes the bond between new clay to old clay to pop apart.  When deconstructing plaster coats that have been applied to each other without dampening the substrate first, the two coats of plaster are quite distinct, and you can easily pry them apart in separate layers, like sheets of slate.  Similarly to 1st coats of plaster, I allow time for water to saturate the clay substrate, because a water slick on the surface will cause new plaster to slide right off the wall.

In order to maximize control over the shape of the walls as well as the quality of the plaster, I do the following:

SIFTING.  I use mostly clay soils to make plasters and there are often stones and large clumps in the mix.  So I sift clayey-soils through a 1/2" or 1/4" screen to break up the soil into smaller pieces.  Basically you want a screen that is slightly smaller than the thickness of plaster you intend to apply (otherwise stones will drag with your trowel against the hard 1st coat of clay).

PROPORTIONS.  I use sand & straw, and sometimes manure, to control cracking in this second coat of plaster.  The reason is because clay expands in volume when wet, which means it shrinks when it dries.  Shrinking clay can translate to cracks in your plaster.  Sand, on the other hand, does not absorb water and so does not increase in volume when wet nor decrease volume when it dries.  So having a high percentage of sand in your mixture helps to control shrinkage of the plaster, and thus cracks.  However, the clay is your binder, it holds everything together and onto the wall, so you need to be sure that your plaster has enough clay to stay sticky, otherwise your will end up with a dusty mess.  The exact proportions of sand-to-clay depend on the properties of your clay, but roughly speaking, I usually end up with between 15% and 30% total clay content, the remainder being sand.  (Note that this includes any sand in your soil, if you are using clayey soil for your plaster.)  The straw component helps to bridge gaps where cracks are likely to occur.  I add a fair bit of chopped straw (3" or less in length) to my second coat of plaster to provide ample structural integrity and I add additional straw when sculpting the clay or where I'm trying to fill in deep holes.  Finally, I use manure whenever it is available, and it is probably my favorite additive for plasters and cob.  The manure is both sticky (like the clay) and fibrous (like the straw), so you augment two properties of the plaster mixture with a single ingredient.

applying the 2nd coat of clay plaste
APPLICATION.  In order to control shaping the walls I use a fairly long (16" to 18") rigid trowel to apply this layer of plaster.  Because the trowel is rigid, I can push the plaster around easily and because the trowel is long, I can create a gently undulating, reasonably flat wall surface.  I find a short trowel does not let me see low spots in my wall surface as well, and I find a flexible trowel just follow the shape of that lumpy, bumpy first coat, so I save shorter, flexible trowels for finish plastering.  If you have a lot of dips in your wall that you want to fill, you will want to add lots of straw to your plaster so it has more structural integrity.  I also limit the thickness that I apply on any one day, and instead, fill deep spots in multiple passes.  Even waiting one day before adding more plaster will allow the first batch of fill to dry enough, and bond to the first coat below, to support more weight of a second layer.  Again, remember that clay is a liquid until it dries, and can only support a limited weight of additional plaster before it tries to flow off the wall.  If your plaster is slumping or falling off the wall, it is probably too thick (or your clay surface below is not adequately damp).

walls become sensuously shaped with sculpted elements
SCULPTING.  This 2nd coat of clay is also the layer that I sculpt into...including niches, wall reliefs, and any clay frames around truth windows.  For thick reliefs, I add a lot of chopped straw, making almost a cob-like mixture, I make sure my surface is saturated with water, and I build up slowly...perhaps 1" in thickness at a time.  If I'm feeling impatient, I use burlap embedded into the surface of the sculpting clay, and I use the burlap to bridge the thick new clay onto the existing wall surface.  (more on burlap below)

using burlap at window sills to prevent cracking
BURLAP.  I use burlap mostly as a preventative measure in places where cracks are most likely to develop, or where the additional strength of surface fiber will be a benefit.  I also use burlap to apply clay plaster to surfaces that otherwise are too slick for plaster to adhere to, such as wood.  So at windows, I use burlap embedded into the surface of the 2nd coat of plaster to prevent horizontal cracking along the bottom edge of the window sill, as well as at the joints between the jambs and the sill (and the jambs and the window head).  The burlap provides exceptional surface tension, and holds the clay together as it dries, so that it cannot crack in those vulnerable locations.  The important trick is that the burlap MUST be fully embedded into the surface of the clay, otherwise it is not bonded and you actually create a loose spot instead of a strong surface.

burlap must embed completely into the clay
I also use burlap where plaster meets wood, and I don't want the plaster to shrink away from the wood, wherever I worry about wide cracks translating into my finish coat, and wherever I want to plaster over a slick surface, like a wood post, any rigid foam, or any roofing felt.  I had one workshop participant declare "burlap is like magic!"  And I pretty much agree!!

leave 1/4" reveal at electrical boxes for finish plaster
ELECTRICAL.  Finally a quick note about electrical boxes...I work the placement of all electrical boxes while installing this 2nd sculpting layer of plaster.  I straighten boxes.  I pull them out if they are recessed too far.  I push them in if they are bulging way past the plane of my wall.  My goal is a level box that sticks out with an even 1/8" to 1/4" reveal from the plane of my 2nd coat of plaster.  Then I can run my finish coat of plaster right up flush with the electrical box, and the cover plates will fit on squarely and tight to the wall surface.  It's also not a bad idea to put a bit of tape over the screw holes to keep mud out.

I'd love to hear other people's experiences and tips!  So please feel free to add comments below.

Resources

If you are plastering over strawbales, read our other clay plaster posts:
"Clay Plastering Strawbales - FIRST COAT"
"Finish Clay Plaster Recipe & Wall Preparation"

These are the most useful books I've found for information on making & applying clay plasters.

            

click the book covers above for more info or to purchase

      
Using Natural Finishes: Lime- & Earth-Based Plasters, Renders & Paints, A Step-by-Step Guide by Adam Weismann and Katy Bryce, Green Books Ltd, 2008

Clay Culture: Plasters, Paints and Preservation by Carole Crews, Gourmet Adobe Press, 2010

The Natural Plaster Book: Earth, Lime and Gypsum Plasters for Natural Homes by Cedar Rose Guelberth and Dan Chiras, New Society Publishers, 2003. 

Comments

  1. Sigi

    I am looking at using jumbo bales that can weight up to 1000bs. Can you render with the bale laying face up and then let it dry before you turn it up vertical allowing a strong bond first to the bale. Also could you lay it down into the render to use it's own weight to force deeper penetration of clay in to the bale then turn it upright to finish it off and let it dry?

    Cheers

    ReplyDelete
  2. Hi, and great question! I don't have experience with jumbo bales...however...you should definitely be able to plaster the bales while they are flat and then tip them into place. Lots of people do this with regular sized bales, usually laying the bales into a clay slip and then setting them into place in the wall. The clay does make the bales heavier, but since you are already dealing with jumbo bales, this seems irrelevant. Dipping bales into slip does indeed result in a great bond between plaster and straw. Let me know how it goes if you experiment with this!
    Thanks, Sigi

    ReplyDelete
  3. HI there,
    I’m running out of time for plastering up here in Montana, so I’m thinking I will make my prettier second coat my final coat for the winter, then someone said to use linseed oil as a finish. What’s your opinion about that and which ingredients would you use for that second and more or less final coat? Thanks!

    ReplyDelete
    Replies
    1. is this inside plaster or exterior? And what type of plaster (clay or lime)? Also, is whatever you are debating about coating with linseed oil going to be the final coat, or would you plan on adding more plaster later?

      Delete
    2. Outside. Clay. And the linseed oil would be to protect through the winter but I’ll need to make repairs next season. Maybe redo a spot or two that didn’t work out.

      Delete
    3. if you are going to add plaster, then you don't want to linseed oil the surface. If it is outside, you also need to make sure your plaster dries completely before winter sets in. (Otherwise the moisture in your plaster expands when it turns to ice, and this can cause rupturing of the plaster.)

      Delete
  4. Hi Sigi,

    We are building bale-cob in Idaho and we are about to plaster the outside of our building, all clay plaster (No lime). Instead of adding manure to our plaster, could we use wheat paste on the second layer instead?

    ReplyDelete
    Replies
    1. gosh, I've never tried that outside, but my instinct would be not to add wheat paste. If you don't have manure, I would just make a good, strong clay plaster and use that. Just note that unless you have really really deep overhangs so rain never hits the walls, you will have some erosion with clay plaster...regardless of additives. The first year is typically the most dramatic, as any texture created by the erosion actually slows down the water, and therefore slows down the rate of erosion over time.

      Delete
  5. Ok thanks! I actually got this a little too late (my fault) and i did add wheat paste to the outside, so i'll let you know how it works. Why, just out of curiosity, would you not add it?

    ReplyDelete
    Replies
    1. Just concerned that if the wheat paste is persistently or frequently damp that you'll get some funky effects, such as black splotches or a funky smell. It's possible you are fine, but my instinct is not to use it outside

      Delete
  6. HI Sigi
    I am building a shower and it has bottles in the top half of the walls. I want to use broken art glass to make a mosaic on the bottom half of the wall, with the top forming a curvey wavey line.
    Is it ok to use clay plaster to fix the glass pieces to the wall and then apply boiled linseed oil as I did to my earthen floor to protect it. I have seen tiled (mosaic) showers and wonder how they are water proofed effectively. How do you usually attach tile to earthen plaster? Your wisdom would be greatly appreciated. The shower floor has a waterproof membrane and is tiled already. This glass mosaic would be going onto a clay plaster wall with no water proofing whatsoever.
    I have seen lime plaster walls coated with wax that have worked and perhaps this would do for the upper half of the shower wall.

    My second question is regarding the lower wall around where my claw foot bathtub is going. What is the best way to apply tile to a clay plaster wall. I need to protect the wall in case there is any splashing from the tub.
    Any advice would be so helpful. I am so ready to have a bathtub lol. Right now I have an outside shower :-)

    ReplyDelete
    Replies
    1. In general, yes, you can use clay as the mastic to affix mosaic tiles to a cob wall. What I'm not sure of, is if this is adequate in a wet setting, like your shower. You might have to experiment a bit with that. Or you can use a lime plaster to set the tiles. But then wait at least 3 weeks before you grout in the gaps or do any sealers.
      (I'm not clear on the difference between your 2 questions...feel free to clarify & I'll do my best to answer)

      Delete
  7. This comment has been removed by the author.

    ReplyDelete
  8. Hi Sigi
    I am working on a straw bale house and plastering with clay. The overhang is about a meter. How do I Best protest the plaster from erosion? Linseed oil?

    And How do I make the insider shower Walls? Will it be Best to use lime plaster? And do I need a membrane?

    ReplyDelete
    Replies
    1. you apply the clay plaster really thick, add lots of straw, and if you have access to cow manure, add that as well. And then do repairs if the clay plaster erodes in a way that is not appealing to you

      for showers, just apply a lime plaster instead of clay...3 coats, with the final coat troweled smoooooth (or you can apply tadelakt as the final coat)

      Delete

Post a Comment